[. . . ] · Always unplug the appliance before carrying out any cleaning or maintenance. · The use of extension leads other than those authorised by the appliance manufacturer could cause damage or accidents. · Never direct the steam jet towards body parts; always handle the steam nozzle with care: risk of scalding!· Always unplug the appliance from the power source before filling the boiler tank. [. . . ] - Place the empty water measure under the MAXI CAPPUCCINO device (3) and release all residual steam inside the boiler by holding down the steam dispenser button (4) (Fig. With the button pushed, it is possible to bring the measure forward into its fixed position, allowing you to take your finger off the steam dispenser button and simply wait for the remaining residual steam to discharge. - When the steam is all out, move the device (3) back to its initial position, pushing it back with the measure (Fig. - Unscrew the safety cap to refill the boiler tank and then follow the steps described here above. WARNING: :The boiler tank cap is fitted with a safety valve which allows it to be unscrewed only if all residual steam has been completely released. Fig. 10 MAKING CAPPUCCINO To make a cappuccino or hot chocolate, or to heat any other beverage, proceed as follows: If the coffee has already been prepared: - Move the power lever (7) to the pre-heat position (Fig. In this position, the boiler tank remains pressurised without dispensing any liquid from the nozzles on the filter holder. - Place the container of milk to be foamed (or liquid to be heated) under the MAXI CAPPUCCINO device (3) and press the steam button (4) to start the jet of steam (Fig. While holding down the button, you can move the MAXI CAPPUCCINO device (3) forwards using the milk container until it is in the fixed position, allowing you to remove your finger from the steam button and to wait until the Fig. 11 Cappuccino and Espresso Coffee Maker Living innovation 6 EC11 milk is ready following the direction of rotation of the device (3) as shown in (Fig. During steam dispensing the sound signal may go on and off, indicating that the boiler is maintaining its temperature. The steam jet shuts off automatically as the MAXI CAPPUCCINO device is brought back into its original position by pushing it back using the milk container (Fig. 10). - Once steam dispensing has finished, move the power lever (7) back to the upright position (Fig. 7) and, using a sponge, clean all residues of the liquid heated from the MAXI CAPPUCCINO device. - If the steam pressure should be insufficient for frothing the milk, fill the boiler again following the procedures described in the paragraph "Successive use". For the best results, we recommend that you prepare the coffee before frothing the milk. If the coffee has not already been prepared: - Fill the boiler tank (as explained in the section entitled "Making coffee") and move the power lever (7) to the pre-heat position (Fig. - When the front indicator light switches off, indicating that that temperature inside the boiler tank has reached the optimum level, the appliance will emit a sound signal. Then place the container of milk to be foamed (or liquid to be heated) under the MAXI CAPPUCCINO device (3) and press the steam button (4) until the liquid is heated or foamed as required (Fig. To make this operation easier, position the device in the fixed position with the help of the container itself, rotating the device (3) forward as shown in Fig. During steam dispensing the sound signal may go on andoff indicating that the boiler is maintaining its temperature. - To stop the jet of steam, release the button (4) or bring the MAXI CAPPUCCINO device back to its original position by rotating it back as shown in Fig. [. . . ] When wiring the plug, ensure that all strands of wire are securely retained in each terminal. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified electrician. Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size. If the fuse cover is lost, the plug must not be used until a replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover. [. . . ]